Mini propeller car

Materials

 

materials to build mini propeller car.

  • 6×15-mm DC motor with 1–mm shaft
  • Mini plastic propeller for 1–mm motor shafts
  • 2xAAA battery holder
  • AAA batteries (2)
  • Toothpicks (2)
  • Plastic beads with hole diameters about the size of the toothpick (4)
  • Cardstock
  • Sandpaper
  • Electrical tape
  • Googly eyes or other decorations
  • Scissors
  • Wire strippers
  • Needle nose pliers
  • Hot glue gun

 

Procedure

  1. Slide one of the plastic beads onto the toothpick. If it does not slide on easily and then spin freely, you need to sand the toothpick down. Sand both toothpicks until all four beads can slide onto them easily and spin freely.
    plastic bead on a toothpick
  2. Use hot glue to attach both toothpicks to the bottom of the battery holder to form axles. Make sure the toothpicks are parallel to each other.
    toothpicks glued to bottom of battery pack
  3. Slide a plastic bead onto one of the toothpicks.
  4. Use the needle nose pliers to cut the pointy part off the end of the toothpick.
    plastic bead on toothpick axle
  5. Use the needle nose pliers to crimp the end of the toothpick to flatten and widen it. This will prevent the bead from sliding off the axle.
    toothpick axle crimped with needle nose pliers
  6. Repeat steps 3–5 for the other three axles. Make sure your car can roll and the wheels do not get stuck.
    car with four plastic beads for wheels
  7. Use the wire strippers to cut the motor and battery pack wires so they are each a few centimeters long.
  8. Strip at least 5 mm of insulation off the end of each wire.
  9. Twist the wires together to form a circuit. Twist the red wires together, and twist the black wire to the blue wire. Optionally, if you have a soldering iron, you can solder the connections to make them stronger.
  10. Wrap the connections in electrical tape to prevent short circuits. If you have heat shrink tubing, you can use that instead, but remember you need to put it on the wires before you twist them together.
    motor and battery wires connected to form a circuit
  11. The propellers come in packs of four because they are intended for use with mini quadcopter drones. There are two clockwise (CW) and two counterclockwise (CCW) propellers. You need a counterclockwise propeller. Hold the propellers as shown in the picture. A counterclockwise propeller’s curved leading edge of the top blade faces to your left (the propeller on the left in the picture).
    counterclockwise and clockwise mini plastic propellers
  12. Firmly press the propeller onto the motor shaft.
    propeller pressed onto motor shaft
  13. Put one AAA battery into the battery holder. It should be the battery where the “+” faces toward the back of the car’s body (the end with the wires). Look for the “+” sign inside the battery holder and make sure it lines up with the “+” sign on the battery.
    single battery put into battery holder
  14. Cut a small piece of cardstock and bend it to form an arch. Glue it to both sides of the back of the battery pack to form a support for the motor.
    piece of cardstock glued to both sides of battery pack to form an arch
  15. Glue the motor to the top of the cardstock, with the propeller facing backward. Bend the wires out of the way so they will not get caught in the propeller.
    motor glued to the top of the cardstock
  16. Add googly eyes or other decorations to your car.
    car with googly eyes
  17. To start your car, insert the second battery. Watch your fingers! The propeller will start spinning right away.
    second battery in battery pack
  18. Put your car down and watch it go! If it spins in circles instead of going straight, check to make sure one of the wheels is not stuck. This will cause the car to turn to one side.
    a mini propeller car moving forward
  19. To turn your car off, remove one of the batteries.
    battery partially removed from battery pack

What Happened?

When you connected the motor to the battery pack and inserted the batteries, you formed a circuit. The batteries sent electrical current through the motor, which made it spin. The spinning propeller pushed air backward, and the resulting reaction force pushed the car forward.

Leave a Comment

Your email address will not be published. Required fields are marked *